Category Archives: Health and Safety

The new guidance relates only to flammable liquids that are stored in containers up to 1,000 litres capacity. There are many workplaces with these kinds of volumes on site – perhaps in warehouses, workshops or garages – that may be unaware of the dangers if flammable liquids are not correctly stored. Each year, many accidents and even fatalities occur due to flammable liquids or their vapours escaping from containers and coming into contact with an ignition source; it’s important therefore that you know how to prevent this from happening.

6 Tips for Safe Storage and Use of Flammable Liquids

1. Complete a risk assessment to determine what could go wrong, taking into account your workplace’s usual work activities and any non-routine work, such as maintenance, where new hazards may appear.
2. If there is potential for a fire or explosion and the risk needs to be reduced, consider the appropriate control measures available. In this instance, you should always be looking to substitute the flammable substance for something less flammable (i.e. with a higher flashpoint) and also remove the ignition source where possible (for example, any welding taking place nearby).
3. All employees working in these environments should have appropriate training which gives them information about how, and why, a fire or explosion could happen and under which conditions. It should cover all activities involving the substance, including moving it, decanting it or clearing up spillages, as well as the general work process it is used in.
4. Your risk assessment should cover the mitigation measures available, which means how you will contain an escape of the flammable liquid if it were to occur, and also minimise its effects.
5. Do ensure that the containers used are suitable for the storage of the flammable liquid – often this means keeping it in the same container in which it arrived. Check that lids are a tight fit and check for dents or scratches which could indicate that the container has been damaged.
6. Have emergency procedures in place which detail how you will evacuate and/or rescue people in the vicinity.

Under the right conditions, it doesn’t take much for a flammable liquid fire to start – make sure that you know how to prevent one from happening on your premises, and also what to do if it does.

Contact us if you require assistance.

What makes this tool so dangerous?

A pneumatic nail gun can drive a nail through almost anything, and shoot that nail a couple hundred metres in a fraction of a second. Never point it at anyone. Never press the trigger unless you’re in position and ready to use the gun. Never keep your finger on the trigger when you’re carrying it. And when you’re reloading it, make sure the air supply is disconnected.

Most injuries occur in construction — about two-thirds of them in framing and sheathing work. Roofing, exterior siding, and finishing are also high on the hazard list.

Q. What are the hazards we should be most concerned about when using nail guns?

A. The biggest danger is an unintended discharge or misfire. When you use the bump or rapid-fire-trigger setting, the risk of injury is twice as high as when you’re using a single-shot, sequential trigger. The work task you’re involved in when you’re using the nail gun can also increase the risk. If you’re in an awkward position, such as a tight space, the gun’s recoil can hurt you. If you’re on a ladder, co-workers below could get hit by accidental discharge. If you need to hold timber in place for nailing, you could shoot yourself in the hand.

Q) What are the most common injuries associated with these tool?

A) Hand and finger wounds make up more than half of the reported injuries, but your whole body is vulnerable. The damage can be serious: bone fractures, paralysis, blindness, even brain damage.

Q) How can we make it safer for our workers to use pneumatic nail guns?

A) Training is the best thing you can do. A supervisor or experienced nail gun user should teach your workers the safest ways of using, carrying, storing, cleaning, reloading, and transporting nail guns. Manufacturers have good safety information in their user manuals; have your workers read them.

Develop written procedures around the safe handling of your guns. Effective supervision also makes a difference; you should regularly check to see that your workers and supervisors are following procedures.

For more information on nail gun safety refer to the manufacturer’s instruction manual.

If you require further information, please contact us.

Are you making these 7 Common Mistakes in your H&S TRAINING provision?

If an accident occurs, one of the first things the HSE will investigate is whether you provided adequate and correct training. In 2 recent fatal accidents, for example, the provision of training was found to be lacking and the companies were fined £361k and £62k.

Common training mistakes include:

●allowing new employees to start working before they have received training

● not providing adequate training for a specific job

● spending too much on training that could have been done in-house

● failing to train staff to report near misses

● failing to see how good manual handling training can save money

● inadequate training for those who might be exposed to asbestos

● not keeping sufficient records

If you require advice please contact us.

If you do happen to be visited by a HSE inspector, it will obviously pay for you to be prepared. Remember that the purpose of any advice given (or action taken) by an HSE Inspector is to make your workplace a safer place for all, which can only be a good thing.

1. Risk assessments, method statements and health and safety policies should all be available on site and should recently have been reviewed to ensure they are suitable and sufficient and cover all work activities.
2. Check that the control measures listed in your risk assessments are actually in place, and are being followed.
3. Ensure that employees, contractors and others on site have all been suitably trained and inducted. Make sure there is evidence of the training available – it’s a good idea to get people to sign to say they have attended so that you have proof.
4. Walk the site regularly – check that people are doing what you’ve stated in your risk assessments. Are they wearing the correct Personal Protective Equipment (PPE)? Are they operating machinery safely? Are vehicles following the safe traffic route as designated by your traffic management plan?
5. Ensure that copies of all thorough examinations/inspections of equipment are readily available, along with any survey reports (for example, asbestos surveys). There’s nothing more stressful than having to search for things during an inspection.

Contact us should you require assistance.

Steps should be taken to manage any risks arising from cleaning and maintenance activity. Manufacturer’s instructions should make recommendations on how to safely undertake cleaning and maintenance of their work equipment and, unless there are good reasons otherwise, these should always be followed.

5 Top Tips for Clearing and Maintaining Machines Safely

1. There are well-known risks associated with machines that have blockages occurring during their operation. Ensure that you fully incorporate these clearing and maintenance operations into your risk assessments. Use control measures such as guarding to prevent access, but also use warning signs as a visual prompt to stop people entering machines.
2. Introduce training – not just for the operation of machines, but also to cover the safe working practices for when things go wrong (such as blockages occurring). Also make this a requirement for all general cleaning (scheduled and non-scheduled) that is needed.
3. Any guarding must be regularly checked. Fixed guarding is usually best, but if removable guards are in place, carry out daily checks to verify they are present before work starts. Interlocking guards can be useful in this instance.
4. Ensure that machines are isolated (turned off) before attempting to clear blockages, and that they can’t be started with the person (or any body parts) in the machine. Carry out visual checks to make sure workers are not in the vicinity before resuming the operation. Physically ‘locking off’ the machine is also useful, to prevent the machine being started by another person.
5. Make sure there is adequate supervision for tasks. Workers may need to have someone there to ask about the correct procedure in the event of a blockage. A good level of supervision can also help prevent people cutting corners to get the job done quicker.

Incredibly, a new worker is as likely to have an accident in their first 6 months with you as during the whole of the rest of their working life. Training for new members of staff must therefore be not only immediate, comprehensive and thorough, but must do everything it can to ensure that the employees have really engaged fully with the need for and detailed demands of accident prevention.

Contact us if you require assistance.